Innovate > Integrate > Empower - Design at Die Level

  Back to List

Bare Die Product Detail: 7808AC

Regulator output > 300mA:
The 7808AC 8-Volt positive regulator delivers 1.5A output current & is ruggedized with internal current limiting, thermal shut-down & safe area protection. No external components are needed other than to enhance performance & design flexibility.
Suiting hybrid & MCM designers needing high reliability with fixed 8V positive voltage regulation. This bare die directly replaces National (TI) LM7808AC, UA7808A & Motorola (MOT) or ON Semi MC7808AC or MCC7808AC.
Features:

    ** PART OBSOLETE - DISCONTINUED **

See 7808 REV 2 for ACTIVE replacement part.

  • 2% voltage output tolerance at 25°C
  • Wide input voltage range
  • Internal Short-Circuit Current Limiting
  • Internal Thermal Overload Protection
  • No external components required
  • Military Temperature Range for High Reliability
  • Provides Point-of-Source regulation with lower noise
  • x2 magnitude impedance improvement with lower bias current and noise when replacing Zener diode/resistor combinations
  • Can be used with power-pass elements to make high-current voltage regulators
  • Negative Voltage complement is 7908AC
    Vendor:
    SiS OBSOLETE
      Electrical Datasheet

    Die Physical Data:
    Footprint: 2.660mm² (4123.013mil²)
      Request Pad Layout
    Product Families: Used for this device are tabulated below.
    Functional:
    • Output: Fixed Output
    • Output Capacitor: Cap Free, Ceramic
    Specification:
    VIN (MIN): 7.00V
    VIN (MAX): 25.00V
    IOUT (MAX): 1.50A
    VOUT (MIN): 7.84V
    VOUT (MAX): 8.16V
    VDO: 2,000mV
    Accuracy: 2.00%
    IQ: 3.300mA
    Noise Figure: 52.0µVrms
    PSRR @ 100KHz:   n/a
    Other Detail: Important information for this device is tabulated below.
    Traffic light setting for Minimum Order Quantity indicates the following:
    • Green:Available from stock or at low factory MOQ.
    • Amber: Available on factory order with MOQ.
    • Red: High factory MOQ may apply, please ask for details.
    Traffic light setting for High Reliability indicates the following:
    • Green: This bare die is specified and tested for use in high reliability applications.
    • Amber: This bare die can meet higher reliability specifications with additional testing & qualification, please ask for details.
    • Red: This bare die is not specified or specifically designed for use in high reliability applications.
    Traffic light setting for Space Grade indicates the following:
    • Green: This bare die is qualified for space applications or has space level qualification data, please ask for details.
    • Amber: This bare die can be specified for space applications with additional testing and qualification, please ask for details.
    • Red: Suitability of this bare die for space applications is unknown and requires further qualification, please ask for details.

    Other Featured Products:

    TL064:
    Quad Low-Power JFET-Input General-Purpose Operational Amplifier
    OPA2333:
    1.8V, 17µA, microPower, Precision, Zero Drift CMOS Op Amp
    CD74HC74:
    High Speed CMOS Logic Dual Positive-Edge-Triggered D-Type Flip-Flops with Set and Reset
    SN74LS85:
    4-bit magnitude comparators
    INN650N080BS:
    650 Volt 29 Amp 60mOhm Gallium Nitride (GaN) MOSFET. Metalized with Aluminum on topside for wirebonding.
    SiS8017:
    4-channel CMOS / LVCMOS Digital Isolator eliminates current noise and provides up to 5kV RMS isolation per UL 1577.